Trying to get a nice clean sound
Moderator: Martin Hairer
Trying to get a nice clean sound
I am attempting to create mp3s.
I have tried using three different USB mics, and no matter what there is background noise starting out. Not sure of the source.
When I choose "denoise" and sample and then apply, it cuts out the background "humming" noise.
But then the places where I am speaking have a faint (not sure of the best term to use) noise in the background. Not a lot, but enough to where you can hear this extra noise ever so much.
I have read the manual and tried all sorts of things but I cannot get a nice clear sounding voice. I did try Frequency Band, DC Offset, and White noise.
Any help would be very much appreciated.
Charlie
I have tried using three different USB mics, and no matter what there is background noise starting out. Not sure of the source.
When I choose "denoise" and sample and then apply, it cuts out the background "humming" noise.
But then the places where I am speaking have a faint (not sure of the best term to use) noise in the background. Not a lot, but enough to where you can hear this extra noise ever so much.
I have read the manual and tried all sorts of things but I cannot get a nice clear sounding voice. I did try Frequency Band, DC Offset, and White noise.
Any help would be very much appreciated.
Charlie
-
- Posts: 379
- Joined: Thu Mar 15, 2007 3:57 pm
Trying to get a nice clean sound
Most probably the noise you are hearing is real ambient noise; you just
don't notice it live; your ear/brain filters it out. If you get a
cardiod mike and get very close to it, you should be able overwhelm it.
What is left, you can probably use the denoise to cut it down.
You could look at the spectrum of the noise and see if it has line
frequency components. If so, you can always use notch filters to get rid
of it. (for US, usually multiples of 120hz)
Chuck
Seishindo wrote:
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
don't notice it live; your ear/brain filters it out. If you get a
cardiod mike and get very close to it, you should be able overwhelm it.
What is left, you can probably use the denoise to cut it down.
You could look at the spectrum of the noise and see if it has line
frequency components. If so, you can always use notch filters to get rid
of it. (for US, usually multiples of 120hz)
Chuck
Seishindo wrote:
_______________________________________________I am attempting to create mp3s.
I have tried using three different USB mics, and no matter what there is background noise starting out. Not sure of the source.
When I choose "denoise" and sample and then apply, it cuts out the background "humming" noise.
But then the places where I am speaking have a faint (not sure of the best term to use) noise in the background. Not a lot, but enough to where you can hear this extra noise ever so much.
I have read the manual and tried all sorts of things but I cannot get a nice clear sounding voice. I did try Frequency Band, DC Offset, and White noise.
Any help would be very much appreciated.
Charlie
_______________________________________________
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
Hi Chuck,
I appreciate your reply. Thanks!
I listened to some podcasts of other people that is use talking, and I cannot hear any underlying hum.
On whatever I record even after cleaning it up I hear a faint underlying hum. So something needs to be different/better.
I have a two year old Macbook
I will take a look at "frequency components" if I can figure that out.
Any other ideas?!
Thanks again.
I appreciate your reply. Thanks!
I listened to some podcasts of other people that is use talking, and I cannot hear any underlying hum.
On whatever I record even after cleaning it up I hear a faint underlying hum. So something needs to be different/better.
I have a two year old Macbook
I will take a look at "frequency components" if I can figure that out.
Any other ideas?!
Thanks again.
Continuing...
Went to Analyze, and then Spectrum.
If I choose the start of a selected portion there is a spike of 16 HZ , -119dB
Varies a bit in different places, but not too far different.
Is that usual?
If it is not, what can I do?
Thanks!
Charlie
If I choose the start of a selected portion there is a spike of 16 HZ , -119dB
Varies a bit in different places, but not too far different.
Is that usual?
If it is not, what can I do?
Thanks!
Charlie
-
- Posts: 379
- Joined: Thu Mar 15, 2007 3:57 pm
Trying to get a nice clean sound
Are you sure you have the display so you can see the entire range from
about 100hz to 1000 hz? 16 hz is of no importance. Are you using log
displacy?
How close do you have the mic to your mouth? Have you tried recording
in a closet?
Chuck
Seishindo wrote:
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
about 100hz to 1000 hz? 16 hz is of no importance. Are you using log
displacy?
How close do you have the mic to your mouth? Have you tried recording
in a closet?
Chuck
Seishindo wrote:
_______________________________________________Went to Analyze, and then Spectrum.
If I choose the start of a selected portion there is a spike of 16 HZ , -119dB
Varies a bit in different places, but not too far different.
Is that usual?
If it is not, what can I do?
Thanks!
Charlie
_______________________________________________
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
-
- Posts: 2
- Joined: Wed Nov 16, 2011 11:10 am
- Location: Sydney, Australia
- Contact:
Re: Trying to get a nice clean sound
I have a similar issue, in that a voice recording that I made has a very noticeable hum, caused by what looks like a dodgy input into the mixer panel. Opening up the spectrum analyser, the main peak is at 50Hz, which makes sense given that this is Australia.CDJonah_alt wrote: You could look at the spectrum of the noise and see if it has line frequency components. If so, you can always use notch filters to get rid of it. (for US, usually multiples of 120hz)
How can I apply a notch filter in Amadeus Pro? If I sample the hum and then use Suppress Noise, the suppression is too good in the gaps where the speaker takes a breath, but either still noticeable when they are speaking, or their voice sounds badly distorted, even to the point where I'm thinking that maybe the hum would be better!
-
- Posts: 379
- Joined: Thu Mar 15, 2007 3:57 pm
Trying to get a nice clean sound
I only AP 1.5.x but on that you go to effects -> denoising --> suppress
frequency band.
You may well also have the overtones 50, 100, 150 ... or possibily 50
150 250 ...
Chuck
On 11/16/11 5:26 AM, CtrlAltDel wrote:
Charles D Jonah
Building 200
Chemical Sciences and Engineering Division
9700 S. Cass Avenue
Argonne, IL 60439
630-252-3471 CDJonah@anl.gov
_______________________________________________
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
frequency band.
You may well also have the overtones 50, 100, 150 ... or possibily 50
150 250 ...
Chuck
On 11/16/11 5:26 AM, CtrlAltDel wrote:
--CDJonah_alt wrote:I have a similar issue, in that a voice recording that I made has a very noticeable hum, caused by what looks like a dodgy input into the mixer panel. Opening up the spectrum analyser, the main peak is at 50Hz, which makes sense given that this is Australia.You could look at the spectrum of the noise and see if it has line frequency components. If so, you can always use notch filters to get rid of it. (for US, usually multiples of 120hz)
How can I apply a notch filter in Amadeus Pro? If I sample the hum and then use Suppress Noise, the suppression is too good in the gaps where the speaker takes a breath, but either still noticeable when they are speaking, or their voice sounds badly distorted, even to the point where I'm thinking that maybe the hum would be better!
_______________________________________________
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
Charles D Jonah
Building 200
Chemical Sciences and Engineering Division
9700 S. Cass Avenue
Argonne, IL 60439
630-252-3471 CDJonah@anl.gov
_______________________________________________
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
Trying to get a nice clean sound
And sometimes *not* getting rid of all the band(s) is the right thing to do.
m.
--
Michael Rees,
composer &c.
Charles Jonah expressed with much marked refinement of phraseology:
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
m.
--
Michael Rees,
composer &c.
Charles Jonah expressed with much marked refinement of phraseology:
_______________________________________________I only AP 1.5.x but on that you go to effects -> denoising --> suppress
frequency band.
You may well also have the overtones 50, 100, 150 ... or possibily 50
150 250 ...
Chuck
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
-
- Posts: 2
- Joined: Wed Nov 16, 2011 11:10 am
- Location: Sydney, Australia
- Contact:
Thanks for the suggestions; I tried using the Suppress Frequency Bands, starting with the peaks at 50, 150 and 200Hz, but it made little difference.
In the end, I tried a trick mentioned on the Audacity wiki, of decreasing the volume of the noise sample before sampling and then suppressing - that way, there isn't a deathly silence where the noise used to be followed by garbled voice. The hum is still there, but it's a lot less irritating.
In the end, I tried a trick mentioned on the Audacity wiki, of decreasing the volume of the noise sample before sampling and then suppressing - that way, there isn't a deathly silence where the noise used to be followed by garbled voice. The hum is still there, but it's a lot less irritating.