Mailing ListMailing List   FAQFAQ   SearchSearch   MemberlistMemberlist   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Move tracks to center or slightly to side

 
Post new topic   Reply to topic    www.hairersoft.com Forum Index -> Discussion
View previous topic :: View next topic  
Author Message
DougWheeler



Joined: 13 May 2011
Posts: 6

PostPosted: Sat Dec 24, 2011 11:41 pm    Post subject: Move tracks to center or slightly to side Reply with quote

Apologies if this has been covered, but I can’t find it. (Perhaps I used the wrong search terms?) I have 4 tracks, 2 of which are vocals. I would like to move one to the center and one slightly to the left. I would also like to take a piece of track 3 (drum) move it let and then back right.
How do I do this?
Thank you in advance,
Doug
Back to top
View user's profile Send private message
craig



Joined: 13 Nov 2006
Posts: 13

PostPosted: Sun Dec 25, 2011 3:35 am    Post subject: Move tracks to center or slightly to side Reply with quote

response deleted

Last edited by craig on Sun Dec 25, 2011 7:30 pm; edited 1 time in total
Back to top
View user's profile Send private message
DougWheeler



Joined: 13 May 2011
Posts: 6

PostPosted: Sun Dec 25, 2011 5:04 pm    Post subject: Reply with quote

Thank you for your reply. I am using version 2.0. Perhaps a fuller explanation would clarify.
Track 1 – female vocal
Track 2 – male vocal
Track 3 – drums
Track 4 – guitar

If you were in the audience facing the group, the female voice is to the left, the male to the right, drums and guitar behind.

I would like the female voice to be placed just left of center, the male voice just right of center, drums left of the female voice, guitar to the right of the male voice. However, I do not want any of them fully left or fully right.

As for track 3 (drums) I have a section of that track I want fully left and a section that is fully right.

In other audio editing software I am used to fader sliders, knobs, or panning envelops. Perhaps I am just missing something?

Again, thanks in advance for any assistance.
Back to top
View user's profile Send private message
craig



Joined: 13 Nov 2006
Posts: 13

PostPosted: Mon Dec 26, 2011 5:01 pm    Post subject: Move tracks to center or slightly to side Reply with quote

My first response was off base since I misunderstood the problem. At
the risk of being unhelpful again, but since no one else that might
know better has responded, I will offer the following suggestion
(again for AP 1.5 but presumably AP 2 has something similar):

If the track is currently mono, convert to stereo using Sound->Convert
Track to Stereo
then adjust the balance using Effects->Stereo Utilities->Balance

For the drum track you would just select part of the track for each
balance adjustment and perhaps use Effects->Fading->Fade In/Out
separately on the left and right channels to get a smooth transition.


On Dec 25, 2011, at 12:04 PM, DougWheeler wrote:

Quote:
Thank you for your reply. I am using version 2.0. Perhaps a fuller
explanation would clarify.
Track 1 – female vocal
Track 2 – male vocal
Track 3 – drums
Track 4 – guitar

If you were in the audience facing the group, the female voice is to
the left, the male to the right, drums and guitar behind.

I would like the female voice to be placed just left of center, the
male voice just right of center, drums left of the female voice,
guitar to the right of the male voice. However, I do not want any of
them fully left or fully right.

As for track 3 (drums) I have a section of that track I want fully
left and a section that is fully right.

In other audio editing software I am used to fader sliders, knobs,
or panning envelops. Perhaps I am just missing something?


_______________________________________________
Amadeus forum mailing list
Unsubscribe / change settings at http://two.pairlist.net/mailman/listinfo/forum_list
Back to top
View user's profile Send private message
DougWheeler



Joined: 13 May 2011
Posts: 6

PostPosted: Wed Dec 28, 2011 11:41 am    Post subject: Reply with quote

Thanks Craig - that sounds like it will work. I will try it when I get home tonight.
Back to top
View user's profile Send private message
DougWheeler



Joined: 13 May 2011
Posts: 6

PostPosted: Sat Dec 31, 2011 2:50 am    Post subject: Reply with quote

OK, still no success. I will simplify the question and post under a new topic.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    www.hairersoft.com Forum Index -> Discussion All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group